Svenskt forum för elektroniksnack.
https://elektronikforumet.com/forum/
Kod: Markera allt
C:\DATA\Xwisp2\xwisp2195> DIR *.HEX
Volume in drive C has no label.
Volume Serial Number is DC26-552D
Directory of C:\DATA\Xwisp2\xwisp2195
2008-01-23 21:41 21 824 Wisp648_123rh.hex
1 File(s) 21 824 bytes
0 Dir(s) 74 893 266 944 bytes free
C:\DATA\Xwisp2\xwisp2195>Kod: Markera allt
C:\DATA\Xwisp2\xwisp2195>xwisp2w
xwisp2 version 1.9.5 for Windows (Jan 24 2008, Open Watcom C/C++ 1.70)
(c) Copyright 2002,2008, R. Hamerling. All rights reserved.
BAUD b : set baudrate b PAUSE "m" : print "m", wait for Enter
BEEP : beep at end of operation PORT x : use port x (name or number)
CHECK : buffer against target PROTECT x : x = ON, OFF or FILE
DELAY d : programming delay (0.1 ms) PUT : buffer to target
DTR x : x = ON or OFF READ f : get, save f
DUMP : display hex image RTS x : x = ON or OFF
DUPLEX m : m = HALF or FULL (Wisp628) RUN : put target in run mode
ERASE : erase target SAVE f : buffer to file
FORCE x : override target with x SELECT x : x = one or more of +-CDFI
FULL : full memory check/verify TARGET x : x = ? or chip name or AUTO
FUSES x : x = FILE, IGNORE or value TIME : show current time
GET : target to buffer VERBOSE : enable screen logging
GO f : erase, write f, check, run VERIFY f : load f, check
HELP : display these screens WAIT n : wait n milliseconds
LOAD f : file f to buffer WRITE f : load f, put
LOG f : log to file f
PASS m : enable passthrough
m = B6T, B6I, AUXT, AUXI
Press 'Enter' to continue:
Specs of following targets were collected from the configuration file(s):
+12F609 16F676 16F818 +16F884 +18F2423 +18F2680 18F452 18F6620
+12HV609 +16F677 16F819 +16F886 18F2431 +18F2682 +18F4520 18F6621
+12F615 +16F684 16F83 +16F887 +18F2450 +18F2685 +18F4523 +18F6622
+12HV615 +16F685 16F84 +16F913 +18F2455 18F4220 +18F4525 +18F6627
12F629 +16F687 16F84A +16F914 +18F2458 +18F4221 +18F4550 18F6680
+12F635 +16F688 16F87 +16F916 18F248 18F4320 +18F4553 18F6720
12F675 +16F689 16F870 +16F917 +18F2480 +18F4321 18F458 +18F6722
+12F683 +16F690 16F871 +16F946 +18F2510 18F4331 +18F4580 18F8410
16F610 *16F716 16F872 18F1220 +18F2515 +18F4410 +18F4585 18F8490
16HV610 16F72 16F873 +18F1230 18F252 18F442 +18F4610 18F8520
16F616 16F73 16F873A 18F1320 +18F2520 +18F4420 +18F4620 18F8525
16HV616 16F737 16F874 +18F1330 +18F2523 +18F4423 +18F4680 +18F8527
16F627 16F74 16F874A 18F2220 +18F2525 18F4431 +18F4682 18F8585
16F627A 16F747 16F876 +18F2221 +18F2550 +18F4450 +18F4685 18F8620
16F628 16F76 16F876A 18F2320 +18F2553 +18F4455 18F6410 18F8621
16F628A 16F767 16F877 +18F2321 18F258 +18F4458 18F6490 +18F8622
16F630 16F77 16F877A 18F2331 +18F2580 18F448 18F6520 +18F8627
+16F631 16F777 16F88 +18F2410 +18F2585 +18F4480 18F6525 18F8680
+16F636 +16F785 +16F882 18F242 +18F2610 +18F4510 +18F6527 18F8720
16F648A +16HV785 +16F883 +18F2420 +18F2620 +18F4515 18F6585 +18F8722
[+] Wisp6x8 firmware >= 1.10, [*] firmware >= 1.12
Press 'Enter' to continue:
Some examples of command lines:
Flash file 'abc.hex' using a Wisp628 on COM1 or /dev/ttyS0 or /dev/ttyd0:
> xwisp2 abc {first serial port is default, 'go' is not required}
Flash file 'abc.hex' using a Wisp628 on COM3 or /dev/ttyS3 or /dev/ttyd3:
> xwisp2 port 3 go abc {'go' must be specified in this case}
The environment variable 'XWISP2' may be set to customize XWisp2 for daily use:
> set XWISP2=baud 19200 rts on {eComStation, OS/2, Windows}
> export XWISP2="baud 19200 rts on" {Linux, FreeBSD}
xwisp2 terminated successfully in 0.00 seconds
C:\DATA\Xwisp2\xwisp2195>
